Last Professional Polyurethane Wood Floor F.Last-n-Last LNL-700A Commercial Grade Oil-n-H20 Wo.Last-n-Last LNL-500X Residential Grade Waterborne.Last-n-Last Absco Polyurethane Wood Floor Finish 3.Last-n-Last Absco Quick Dry Polyurethane Primer-Sa.Heavy finish application, high humidity or lack of airflow will extend drying times. Drying Time : When applied according to directions, and in thin coats, Last nLast 1500 should be dry to the touch in 1 hour. Last-n-Last Absco Polyurethane Wood Floor Finish 5. Make sure the stain is completely dry before applying the finish or sealer.Last-n-Last Absco Polyurethane Wood Floor Finish 4.Zinsser Bull Eye Zero and Bull Eye Shellac. Last-n-Last Marine and Door Spar varnish Oil-n-H20.Last-n-Last Grand Oil-n-H20 Wood Floor Finish.Last-n-Last TREK PLUS Commercial Grade Waterborne.Last-n-Last LNL-1500 Commercial Grade Waterborne W.Part Alternates: LAST N LAST CLASSIC WOOD STAIN, LAST N LAST FRUITWOOD. Lass-n-Last LNL-100S Commercial Grade Waterborne W. It may be a mixture of colored pigment, wood preservative, drying oil and.Last-n-Last LNL-100SA Commercial Grade Oil-n-H2O W.Zip-Strip Premium Paint & Finish Remover.Zip-Strip Industrial Paint & Finish Remover.Zip-Strip Trigger Spray Paint & Finish Remover.If waiting longer than 24 hours between coats, sanding is recommended. Allow minimum of two hours between coats, or until thoroughly dry. Remember to vacuum and tack thoroughly after screening to remove all dust. Screen the work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar. To prevent lapping and dry marks, be sure you are using the recommend coverage. Missed areas can be touched up if seen right away. If pushed too hard or fast, drips will fly off the applicator. At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge. Holding the applicator at a snowplow angle will maintain a wet edge at all times.( Maintain at least 3” wide wet edge to ensure proper coverage). Using a clean pre-dampened waterborne applicator, pull forward with the grain of the wood, moving the finish towards the opposite wall. Apply the finish with the grain of the wood. Pou a 6-8” wide line of the finish along the starting wall. Last 1500 looks milky when applied, but will dry to a clear, beautiful finish.It does not store any personal data.Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. The cookie is used to store the user consent for the cookies in the category "Performance". This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other. The cookies is used to store the user consent for the cookies in the category "Necessary". The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional". The cookie is used to store the user consent for the cookies in the category "Analytics". These cookies ensure basic functionalities and security features of the website, anonymously. Sand all cleaned wood using 80-120 grit sandpaper for vertical surfaces and 60-80 grit sandpaper for horizontal. Allow the surface to dry for 48 hours, or to have a moisture content of 18 or less before application. Absolute Coatings Inc are dedicated to providing all flooring professionals and do-it-yourselfers, with the most complete line of high quality wood finishes available. Necessary cookies are absolutely essential for the website to function properly. Power wash wood surface clean with fresh water using 500- 800 psi with the nozzle 8-12 inches away to remove cleaning solution. Last n Last Absolute Coatings Inc is a leader in the wood flooring industry.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |